After whittling down the chopstick a little for a nice tight, yet smooth fit in relation to the bore of a pen all you need is a chopstick, rubber band and the body of a pen. For any kids or unknowing adults, this is for target practice only. Much like an actual firearm, do not point this at or towards anyone and wear eye protection anytime you decide to operate any weapon like this. This is meant to be a fun target practice activity.
Amazon link. Disposable Chopsticks, pack of 40 pair: https://amzn.to/31xeWeJ
Mouth watering video "How to Grill Steaks In Singapore | Deliciously Juicy Australian Steaks Cooked Medium Rare and Well Done". Cooked these tasty slabs at for a few different time frames as there were three different requests, one barely cooked (a lot of red inside), one medium and the other well done. I grilled these up with a little bit of Johnny's on each side. They turned out delicious. I did cut the fat off a little on two steaks(per request), and the left it on the third. Hard to beat feasting on freshly grilled steak with a baked potato.
In this DIY How to Remove and Clean Clothes Dryer Vent Ducting for Fire Prevention Video I take you step by step through this simple yet necessary process. Many fires are started every year from lack of cleaning of dryer vent ducts. Once this method and processed is used, your ducting will be just like new. The first thing to do is remove and replace the slinky looking aluminum vent that connects the dryer to the hard vent. This is usually accomplished by the loosening and removal of the large hose clamp, typically a flathead fastener.
Once I got this old dryer vent removed I used my shop vac and got the big stuff out. If you are not planning on disassembling the whole thing you need to be able to have enough shop vac hose to reach the full length of the whole vent run or at least enough so that you can reach the remaining distance from the outside or opposite side. In the case in the video I decided to remove the whole thing and actually replace the old vent with brand new stuff. The existing was at least 20 years old and was corroded, old and sagging. If you wanted to re-use the existing vent ducting and remove it for cleaning, bring it outside and blow it out with an air compressor. There is a good chance you'll still have some scum that won't readily blow out with an air compressor so you'll need to figure out how to manually remove it. Many times this can be done with a rag or some type of cleaning brush. If you don't remove the old scum and reinstall it, it will be a starting point for new dryer vent bi-products to accumulate reducing the time that you'll need to clean it out again. When reinstalling be sure that the seams are facing the direction of flow so it won't be a sticking point for debris to collect. Once you get your vent ducting run all cleaned out and re-assembled it will give you piece of mind that you've reduced the chances of a dryer vent duct fire.
MACTREM Brand LED Ring Light Kit-Unboxing, Assembly and Review; Part# M-A001. This light assembly is super easy to put together and use. The light has many different levels of lighting as well as different types of light (i.e. white light, yellow light, etc.). This is all adjusted on a switch adjuster that is very user friendly. Great for pictures and videos. There are actually two assemblies with this kit. One for the light and one for your phone/camera. This kit comes with two versatile tripods so you can adjust both your camera and light at any angel you wish. Using the contents of this hit will fully enhance your filming and photography experience. It plugs into a USB which I demonstrate can be operated off of a lap top or a plug in the wall. This would also be a nice addition for the ladies who are doing their make up.
Kitchen sink spout spraying all over? Not getting enough water flow from the sink faucet? It's likely the faucet spout filter is clogged. In this tutorial I show you the simple process for accomplishing just that. I didn't realize it until I removed the old one that it needed to be replaced with a new one. This won't be the case all the time as you may just be able to clean the old one off of sediment, plastic, etc and reinstall it. In my case, the filter was damaged therefore not doing it's job. I do filter all of the water but this screen holds back the big particulates. I couldn't believe how much crap had built up on my filter. I'm surprised it flowed as well as it did. Amazing how much stuff is in our water. Changing this thing out is simple. Mine takes a 22mm wrench. Take the 22mm wrench (or vice grips if you don't care about the finish) and turn it counter clockwise to loosen. Once off, clean it all off and inspect for damage. If damaged, then replace. If still good, reinstall. The screen that I removed did not have a gasket but luckily the new one came with a gasket. If you are going to get a new one I recommend you take the old one to the hardware store with you to match it up. Pull it out of the package in the store and be sure it's the correct size and thread pitch. There is not a huge risk here for the most part as many of them are standard size. I believe the technical name for these is a sink faucet aerator.
This was a fun little welding fabrication project. I found myself with a stack of old steel thick lawnmower blades. I thought what a better idea than to make a homemade machete with them. I used full penetration weld joints. "V" groove joint design both side. I gouged out the opposite side until I got down to clean sound metal, then welded it up. The trick here was to watch my distortion. So rather than weld one side all the way out I welded each side just below flush and then put the covers on it. Once I welded it out I ground the welds so that they were ground flush and indistinguishable from the base metal. I then marked out a radius for the blade and then a cut out portion for the handle. I then used my hand held electric angle grinder with a cutting wheel to complete the cuts. I honed the blade with a flapper wheel. I then used some wrapped twine for a handle. This was the first of it's kind that I made.
I purchased this new Kwikset Brand Door handle and deadbolt kit from Lowe's for about $40 or so. Got the kit home and started unboxing it and setting my parts out prepping them for installation. I gave it a rough assemble just to see how it is all going to go together so I had an idea of what to expect once I put it in the door. To get the process started for the door handle itself, I put the latch core inside the door for a test fit. The nice thing is that almost all doors come with standard size pre-drilled and prefabricated holes to accommodate standard door handle kits. The next step was to loosely insert the inside and outside door handles for a rough fit up. Now I inserted the long set screws in through one side and threaded them into the opposite side (inner to outer). I screwed them down snug with a Phillips head screwdriver. Then I slide the decorative collar of that and it just snaps on. After that comes the handle itself. I slid the handle on and tightened it down with an Allen wrench which comes with these types of kwikset kits. I then did the same thing with the other side. For the next step I screwed in the two screws for the latch that secure it to the door. I tested for smooth operations with no binding or sticking.
Deadbolt portion:
I inserted the latch or core of the dead bolt into the door for a test fit. After knowing that it fits well it was time to place both halves of the dead bolt locking assembly into core or latch portion. The somewhat semi circular shaft fits snugly into the latch insert. Once fit up I lined up the set screw holes so they can be seen from the opposite side. Then it was time to insert the set screws and secure them tight. I ensured smooth operation with no sticking or binding. The door is now capable of being fully secured.
Kwikset Door Knob and Dead Bolt Installation Tools Needed:
