Made my first ever DIY Hand Forged MidEvil Long Twisted Spoon Tutorial Demonstration [How to Forge a Spoon] as a present and it was a lot of fun. Used a propane burner and pounding block to hand made this big spoon.Once forging was complete I coated it in linseed oil.
Placed a nice metal fire ring inside the brick for easy clean up and decoration. One nice thing about living where I do is that it's legal to have little backyard bonfires. Many good times are had with get togethers around a fire. I needed to move locations of my fire pit so I decided to make a video while I made this new one. To get started I marked a counterpoint in the middle of my rough circle and started over turning the dirt with a shovel and breaker bar as it was very tough and rocky. Then I started digging out the hole in the ground deep enough to accurate the height of my fire ring that I wanted to put in the ground. I decided I wanted to inset this one into the ground for the most part rather than have it be mostly above ground. Once I dug enough dirt out to where I thought it would be deep enough, I started to test fit the metal fire ring for depth purposes but then I also used it as the template for which to create the circular brick portion around. With my digging tools I started widening the circle a little bit to make it large enough to fit the bricks. It was important to keep the bottom flat so the the bricks would be level. Once I got the bottom of the pit level I used my 3 foot level to make sure it was level. I was then able to stack all of the bricks in there in a circular pattern and then add the metal fire pit inside it. It turned out just as I planned and ended up using it quite a bit.
To make this fun urban survival style DIY Kiwi Shoe Polish Can Alcohol Stove and be able to Cook Egg on a Cast Iron skillet over it's hot flame you'll first want to obtain some alcohol, a kiwi shoe polish can, a cordless drill or at least something to drill holes with. You'll then want to drill numerous tiny holes in the top lid of the kiwi shoe polish can. You'll then want to pop the lid back on after filling it with the isopropyl over the counter alcohol. Then you can go ahead and light it. This makes for a fun homemade burner project.
Amazon link to Kiwi Shoe Polish Can: https://amzn.to/32RRYy2
This was a very fun welding fabrication project. Although I had a couple fire pits this one fit really well onto the back patio for use making smaller fires. My neighbor, who is an automotive mechanic, gave me an old empty coolant container. Knowing I was a welder who liked to tinker and weld junk metal together, he always brings me interesting parts to make stuff from.
I made sure it was empty by drilling a hole into the top first just to be sure there wasn't anything left in it. Using an electric corded angle grinder I cut the top off the container. There was a weld seam around it that I used as a guide or cut line. I had some 1/4" wide flatbar laying around that I bent into a circle matching the same diameter as the tank. The flatbar was very soft so I was able to bend it by hand and weld the end together. Using the same size flatcar, I cut 4 riser pieces approximately 6" long and ground the mil scale off the ends to shiny metal. This makes a better surface to weld. I then welded those risers to the bottom larger portion of the container. I then welded the circular flatbar piece to the 4 risers. This portion is in an effort to create somewhat of an access or viewing window to the flames that will live inside the tank as well as create a seat for the top lid to set upon. I had some wire mesh laying around to it seemed natural to cut out a section and wire tie it to the viewing window (access) portion of the fire pit. I would have like to weld it in place but it's too thin so I decided to use metal wire instead. I drilled holes to for which to run the wire through and secure it in place.
For the legs, I had some rebar laying around so it seemed like a good idea to use these to bring it off the ground a bit. While welding these it's important to focus your heat on the rebar as the tank wall is very thin. If you sit on the tank wall too long or apply too much heat to it, you'll blow right through the wall. I tacked them all in place first and didn't get in a hurry thereby keeping them cool before proceeding to weld more.
I had some other bent round stock laying around so it seemed like a good use for some handles to move the thing with. I cut and welded those on in the same fashion as the legs.
I went and purchased a can of high heat paint for the local hardware store and applied a couple coats. I was very happy with the results. The guitar playing is me just messing around as these videos are an excuse for me to play and use it for theme music.
Three different styles of smoke alarms and how to change the batteries on them. Smoke alarms will beep if they are getting low on batteries. If you suspect they are out or low, just replace the battery. Check them often and have more than one in a each area in case one happens not to work. It's a good idea to check these once every few months. You can test them by pressing the button on the front of the smoke alarm. If it doesn't make a loud beep when you push it, then the battery is dead or the smoke alarm is bad and should be replaced immediately. It's a good idea to have a smoke alarm in each room. There is no reason not to as they are very affordable and they are proven to save lives.
