DIY Allen and Roth Blackout Window Shade Installation Demonstration [All...

This Allen and Roth window shade was super easy to install and can be accomplished in a matter of minutes. I used a cordless drill for securing it's only two brackets to the interior of the window frame. Purchased at Lowe's. They are light weight and keep the sun from blasting through the window as well as provide maximum privacy. I take you step by step through the process in my "DIY Allen and Roth Blackout Window Shade Installation Demonstration [Allen and Roth Blackout Shade]" video. Hey guys get some blinds i'm gonna put up here these allen and roth blinds but this is the before picture 47 inches across here's the blinds that we're going to be using Okay again this was 47 inches across and these are 46 so you can see there's a little bit of a gap in there which is what you want which is the window seal will kind of make up that gap as well but if we did it on the full 47 i'm not sure that this would fit here's the brackets for these things okay we have a choice of either doing an inside mount like this or an outside mounting outside the frame here okay see those two dots there those are the marks i made with the pencil and i just made that because i'm going to pre-drill my holes right there Now we're going to screw these into the two holes we just made to secure the bracket to the overhead all right we got our brackets up i'm just gonna pop the thing in there just snaps right in there gonna angle it down this piece is the handle to pull the shade down and it just grabs that lower edge you just snap it right on there i'll show you okay this is the upper portion so this just grabs that lip right there here we go That was too easy Thank you.

DIY Forging a Door Pull and Drawer Handle From Old Hardened Steel Tool [...

In my "DIY Forging a Door Pull and Drawer Handle From Old Hardened Steel Tool [Blacksmith Forged Door Pull]" I show how I hand forge some cool textured vintage looking door pulls/handles. I heated up the full length of some old tool steel and bent it around to my desired shape then flatten out the ends for a decorative look. I chose to drill the holes in each side. I coated this one with rustoleum spray paint but immediately regretted it as I should have just done my normal treatment to it with wither WD-40, linseed oil, or some bee's wax. Fun project and thought this was. a great repurposing of some old rusty tool steel that hasn't been used in over 20 years.

Double Burner Gas Propane Forge Furnace Blacksmith Knife making w/ 1 Door:

https://amzn.to/34K2cac

Please stop by my website: https://www.diy-technician.com

DIY GateHouse Hinge Pin Door Stop Installation Tutorial Demonstration [G...

DIY GateHouse Hinge Pin Door Stop Installation Tutorial Demonstration [Gatehouse Hinge Pin Doorstop]. The first step is to buy a couple of these and then pop the hinge pin on the door. I used a small screwdriver and lightly tapped it out of place. I installed these individually one by one. Once the hinge pin is removed I pushed the door stop down over the hinge pin and tapped it back into place. Once installed the hinge pin doorstop can be adjusted to your desired setting to either open further or open less. In this case I needed to keep the door knob from hitting the glass closet doors and causing a huge destructive mess so it was mandatory I put these on. Super easy installation and quick too. The door stops are cheap compared to a hole in the wall or a busted closet door. Thank you for watching and please leave me a comment or two. 

Here's a paid link to a similar one on amazon:

Ives by Schlage 70A10B Hinge Pin Door Stop:

https://amzn.to/3zEZxbB

Please visit www.diy-technician.com

DIY Home Brew: Northern Brewer | Dead Ringer India Pale Ale Kit

I ordered this awesome beer kit from amazon. In this DIY Home Brew: Northern Brewer | Dead Ringer India Pale Ale Kit video, I take you step by step through unboxing, brewing and taste testing. This was ready to drink in just over a month. The first thing I did was heat approx 2.5 gallons of filtered water to 155F or approx 68F. Then take the provided grains, pour them into the grain bag, tie off the grain bag and place it into the water once it reaches temp. Maintain that temperature, no higher and no lower (plus or minus a couple degrees), and let it steep for 20 to 30 minutes. Once 20 to 30 minutes has elapsed, pull out the grain bag and let drain over the newly created wort. Don't squeeze it. Then it's time to bring the wort to a slow rolling boil. Total boiling time will be 60 minutes. Once boiling add the liquid malt extract. and stir in well. While it's boiling I added cool filtered water to the fermenter. I then added hops at 10 minutes time intervals and stirred them in. Once 60 minutes in complete I transferred the wort immediately to an ice bath. Once completely cooled I transferred (siphoned) the wort to the fermenter and topped it off with some additional filtered water. I then added the yeast and shook it around a little. Then I installed the air lock and let the brew sit for a couple weeks in a dark area. After a couple weeks I transferred it to a separate fermenter that was actually only used as a bottle filler and then mixed and added some hops and the priming sugar solution to give the brew carbonation. I then bottled it and let it sit for a couple weeks before sampling.

How to Construct a Brick Fire Pit in your Back Yard

Placed a nice metal fire ring inside the brick for easy clean up and decoration. One nice thing about living where I do is that it's legal to have little backyard bonfires. Many good times are had with get togethers around a fire. I needed to move locations of my fire pit so I decided to make a video while I made this new one. To get started I marked a counterpoint in the middle of my rough circle and started over turning the dirt with a shovel and breaker bar as it was very tough and rocky. Then I started digging out the hole in the ground deep enough to accurate the height of my fire ring that I wanted to put in the ground. I decided I wanted to inset this one into the ground for the most part rather than have it be mostly above ground. Once I dug enough dirt out to where I thought it would be deep enough, I started to test fit the metal fire ring for depth purposes but then I also used it as the template for which to create the circular brick portion around. With my digging tools I started widening the circle a little bit to make it large enough to fit the bricks. It was important to keep the bottom flat so the the bricks would be level. Once I got the bottom of the pit level I used my 3 foot level to make sure it was level. I was then able to stack all of the bricks in there in a circular pattern and then add the metal fire pit inside it. It turned out just as I planned and ended up using it quite a bit.

DIY Instructions-How to Install an Automatic Ice Maker in Your Refrigera...

How to Install and Automatic Ice Maker. This installation was for a Frigidaire brand. IMEZC000 model. Automatic Ice Maker Installation kit. After unboxing the ice maker, you'll notice that there is an electrical connector that needs to be hooked up. Keep that in mind. The ice maker will need an on demand water supply so you'll need to run a water line to the fridge. Almost all models nowadays have a standard hook up in the back of the fridge for this. When I did this, I removed the thread protectors from the fridge connection and used teflon tape around the threads. Then I hooked up the hose, turned on the water and checked for leaks. In this video you'll notice my incoming water valve demonstrates some leaking while operating the valve. Once it's either in the fully open or fully closed position, the leak stops. I did end up replacing this valve just for the purposes of upgrading it and made another video on it as well. After the water connection at the fridge was satisfactorily checked for water leaks, I pushed the fridge back into it's spot. Now it's time to mount the ice maker. The electrical connections are uncovered inside the the freezer. There are some plastic screw hole protectors in the side of the freezer that need to be removed to allow for the mounting screws to be inserted. Then I inserted the mounting screws that come with the ice making kit. Don't screw them in all the way. Pull out your ice maker and plug the electrical connection into the receptacle in the freezer. Also there is a plastic ice slide that needs to be installed as shown in the video. After plugging in the electrical connection I hung the ice maker onto the mounting screws and then drove them in all the way to secure it to the side wall of the freezer. I then plugged the fridge back in had ice in no time flat. This ice maker installation was so easy.



Link to similar ice maker on amazon; https://amzn.to/2JUTwRO

DIY Pallet Project: Shop Table From Pallets-Repurposed Wood Made Into Us...

In this DIY Pallet Project: Shop Table From Pallets "How to" video, I take you step by step through my process on using old pallet wood to create a shop table. For the Table top, the first step was to get all my slats separated, get the nails pulled out, and clean them all up. I cut them all to the same length and placed them on two longer aluminum clamps. Pipe clamps work well here too. Once I get them square, flat, and straight, then I took two perpendicular lengths of wood and drilled and screwed them up through the bottom to hold it all in place. I then drilled and screwed 4 equal legs on. I then cut a couple of blocks for extra reinforcement, drilled, and screwed those on as well in between the legs and the cross members on the underside of the pallet table surface. I custom made the metal angle iron brackets as well. I had some old metal bed rails laying around so I sectioned them up and drilled holes in them to facilitate screws and used them for reinforcing brackets. I used some repurposed lag bolts to secure these. I sanded the top surface of the table so it was nice and smooth and flat. I decided that I needed a shelf down below for extra storage so I hit up my pallet pile again. I pulled off some more slats carefully so as not to crack or break the boards in the process. I got the nails all pulled out and cut to length on the table saw. I used some of these for the trim around the top of the table so it had a nice finish. I then created the second shelf down below using more pieces from the pallet pile and nailed them together with a brad nailer.
Tools used:
Table Saw: https://amzn.to/31W6epw
Cordless Drill: https://amzn.to/31WRgiO
Brad Nailer: https://amzn.to/30UA50b
Air Compressor: https://amzn.to/35ftvop

DIY Kwikset Door Handle and Dead Bolt Installation

In this "How To" DIY Kwikset Door Handle and Dead Bolt Installation, I take you step by step through the installation process after I replaced my front house door to an upgraded model.

 This was a first of it's kind for me as the handle was a little bit different style than what I'd done before. It'd still turned out though.

The first thing you'll want to do is remove all your parts from the package then lay them out on a table or the floor next to your door.

Take the door knob insert and test fit it into it's hole in the door and make sure you know which way it's supposed to face depending on which way the door swings and closes. In this demo I did a test run on how the handle mechanism operates outside of the door prior to installing just so I understood and could see what was going on with the thing. I put the insert and the large handle portion in the door loosely. The smaller handle portion needs some assembly.

Now loosely assemble the rest of the parts in the door as shown. Tighten the smaller door handle first via the Allen head set screw. Now go ahead and tighten everything down.



www.diy-technician.com



Tools you'll need for this job:

Cordless driver or manual Phillips screwdriver: https://amzn.to/31S3OIi



Allen wrenches: https://amzn.to/3396IZz

DIY How to Fix a Gas Stove Burner That's Not Working-Simple Fix Using Ju...

If all of your other gas burners are working but one isn't,  it's likely that you have a cleanliness issue in the bottom gas inlet beneath the burner's metal parts on the stovetop itself. It's a very simple fix once you know how to do it. This is a common problem with gas stove burners. If you have a small paperclip handy, this will work just fine. Better yet, if you have a set of torch tip cleaners, even better. If you don't have any, you should buy some. I've provided the link below for a set of these and they are perfect to keep around for when this happens to you. They are so cheap there's no excuse for not owning some, especially when it means not being able to cook.

Before working on this or any other gas system make sure you turn off the gas, even for a little fix like this because you will be somewhat up close and personal to where the gas exits into the "bowl" portion of the burner located beneath the special metal parts. After turning off the gas you can now start removing the components that make up the burner portion. Most of them just kind of sit on top of each other. Once you have removed all the burner parts and set them off to the side you can now take your cleaner from your set of tip cleaners or your small paperclip and ream out the gas oriface in the center at the bottom. Be sure to get a tip cleaner or paper clip that fits just snug as you don't want to force it in there or wind up breaking it off while a portion of it is stuck inside the oriface (then it will never work). Now reassemble the metal parts that make up the burner. Turn the gas back on and light the burner. If it doesn't work at first try the process one more time. If it still doesn't work after that you likely have another issue that is causing the problem and call a professional.



Summary of this DIY fix is as follows:



Step one: Shut off gas

Step two: Take it apart

Step three: Obtain small paperclip

Step four: Clean out bottom gas oriface with paper clip

Step five: Re-assemble burner parts

Step six: Turn gas back on

Step seven: Light burner



Tip Cleaners: https://amzn.to/2osoQ1o

How to install window screens on house windows

Step by step tutorial in the basics of installing a window screen. The side with the thin metal springy clips attached to it goes in first. The plastic tabs go inward as it makes it ever so slightly tougher to remove from the outside. The trick to getting all four corners inserted is to get three corners in first leaving one slightly out, then the fourth and final corner will barely slip in. In this example I put the right two corners in first because they had the metal spring tabs on them, followed by the upper left corner, then finally the bottom left corner.

Not sure if this is any good: https://amzn.to/34XDKNl

www.diy-technician.com

How to Install an Automatic Ice Maker

This was a really easy installation. Anyone can do this. This installation assumes a water line has already been run. So you must shut off and  connect the water line as shown in the video to the connection on the bottom of the refrigerator in the back using teflon tape for the connection to prevent leakage. Create room in the freezer for your ice maker then pop the plastic cap over the wire connection. Remove the caps inside the freezer for mounting the ice maker. Screw in the mounting screws to the designated holes. Connect the wire connection from the ice maker to the freezer. Hang the ice maker on the mounting screws then finish screwing them all the way in securing the ice maker. Don't screw them in too hard b/c the plastic could break but just tight enough to keep it snug. Plug fridge back in and turn on the water. Works like a charm.

Troy Bilt Lawnmower Unboxing Assembly and Usage Model 421854

DIY Shower and Bath Tub Drain Unclog-Drain Surgery

Shower drains get plugged up all the time especially if you have girls in the house. One must get the fine art of unclogging drains down to a science unless you'd prefer to foot the bill for someone else to come and do it. A good DIY technician should be able to get this job done in under a half and hour depending on severity. A good pair of hemostats is very handy for this job but if you don't have hemostats, do not worry as either needle nose pliers or even tweezers will work. Ideally, the water will be drained when you are working on this but many times you'll find yourself working in standing water. In this case the water slowly drained so I could at least stand above where I was working. The trick here is to take of this problem once the drain starts draining slowly, NOT when the drain completely quits draining. So, once you have the drain plug unscrewed (turn counter clockwise to unthread), then take your extraction tool and start to slowly remove the nasty hair and whatever else is attached to it from the drain. Repeat until the drain is free of any foreign material and is like new. Test to ensure proper drainage before walking away. In most situations similar to this there is an accompanying odor that you'll notice so you may want to have some kind of small trash receptacle nearby for which to deposit your removed debris. Good luck fellow DIY Technicians.

How to change smoke alarm batteries-Three different styles

Three different styles of smoke alarms and how to change the batteries on them.  Smoke alarms will beep if they are getting low on batteries. If you suspect they are out or low, just replace the battery. Check them often and have more than one in a each area in case one happens not to work. It's a good idea to check these once every few months. You can test them by pressing the button on the front of the smoke alarm. If it doesn't make a loud beep when you push it, then the battery is dead or the smoke alarm is bad and should be replaced immediately. It's a good idea to have a smoke alarm in each room. There is no reason not to as they are very affordable and they are proven to save lives.

DIY Portfolio Brand Motion Detector Light Installation