DIY Allen and Roth Blackout Window Shade Installation Demonstration [All...

This Allen and Roth window shade was super easy to install and can be accomplished in a matter of minutes. I used a cordless drill for securing it's only two brackets to the interior of the window frame. Purchased at Lowe's. They are light weight and keep the sun from blasting through the window as well as provide maximum privacy. I take you step by step through the process in my "DIY Allen and Roth Blackout Window Shade Installation Demonstration [Allen and Roth Blackout Shade]" video. Hey guys get some blinds i'm gonna put up here these allen and roth blinds but this is the before picture 47 inches across here's the blinds that we're going to be using Okay again this was 47 inches across and these are 46 so you can see there's a little bit of a gap in there which is what you want which is the window seal will kind of make up that gap as well but if we did it on the full 47 i'm not sure that this would fit here's the brackets for these things okay we have a choice of either doing an inside mount like this or an outside mounting outside the frame here okay see those two dots there those are the marks i made with the pencil and i just made that because i'm going to pre-drill my holes right there Now we're going to screw these into the two holes we just made to secure the bracket to the overhead all right we got our brackets up i'm just gonna pop the thing in there just snaps right in there gonna angle it down this piece is the handle to pull the shade down and it just grabs that lower edge you just snap it right on there i'll show you okay this is the upper portion so this just grabs that lip right there here we go That was too easy Thank you.

DIY GateHouse Hinge Pin Door Stop Installation Tutorial Demonstration [G...

DIY GateHouse Hinge Pin Door Stop Installation Tutorial Demonstration [Gatehouse Hinge Pin Doorstop]. The first step is to buy a couple of these and then pop the hinge pin on the door. I used a small screwdriver and lightly tapped it out of place. I installed these individually one by one. Once the hinge pin is removed I pushed the door stop down over the hinge pin and tapped it back into place. Once installed the hinge pin doorstop can be adjusted to your desired setting to either open further or open less. In this case I needed to keep the door knob from hitting the glass closet doors and causing a huge destructive mess so it was mandatory I put these on. Super easy installation and quick too. The door stops are cheap compared to a hole in the wall or a busted closet door. Thank you for watching and please leave me a comment or two. 

Here's a paid link to a similar one on amazon:

Ives by Schlage 70A10B Hinge Pin Door Stop:

https://amzn.to/3zEZxbB

Please visit www.diy-technician.com

DIY Beer | Brewer's Best Robust Porter | Basic Step by Step "For Dummies...

DIY Home Brew | English Brown Ale | Craft Beer Recipe Kit | Brewing to T...

Follow along step by step during the video.  DIY Home Brew | English Brown Ale | Craft Beer Recipe Kit | Brewing to Taste Test. This turned out really good and got better after 3 to 4 weeks.
The first step was pouring about 2.5 to 3 gallons of filtered water into my brewpot. This brew kit came with grains to steep and make the wort as well as liquid malt extract and dried malt extract. The grains must be steeped in the brewpot. Once you steep them, much like tea, don't squeeze the grain bag after steeping, rather just let it drain. This is what make the wonderful wort. Now bring the wort to a rolling boil and add the liquid malt extract, the aromatic hops and the dried malt extract. Boil it for around and hour then cool it down as quickly in an ice bath or use a wort chiller. Once cooled down I then added the wort to my fermenter and added filtered water to the 23L mark. I then added the yeast. Once the yeast is added the brewing is complete. Now I let it ferment for 2 weeks. Once the 2 weeks was up I bottled it. I mixed and added priming sugar to the fermented brew right before bottling. After bottling I let it sit in the bottle for minimum of two weeks. Before partaking, I placed in the refrigerator to chill.

Here's the link to it: https://amzn.to/2TR2nag

DIY Home Brew | Octoberfest with Mosaic Hops | Craft & Brew Beer Recipe Kit

DIY Home Brew | Octoberfest with Mosaic Hops | Craft & Brew Beer Recipe Kit. I was very happy with the way this turned out. I had to use Mosaic hops b/c when this kit showed up the package had been damaged and the hops missing. I had some mosaic hops on hand so I used those. I turned out amazing tasting and very unexpectedly unique. These beer kits make the best beer. I don't buy beer at the store anymore since making my own. Making your own beer gives you a deeper appreciation for it. You realize what goes into making it and the ingredients involved. You can have this brewed on your brew day in less than two hours. I left it in the fermenter for two weeks, then two more weeks after bottling.

DIY Home Brew: Northern Brewer | Dead Ringer India Pale Ale Kit

I ordered this awesome beer kit from amazon. In this DIY Home Brew: Northern Brewer | Dead Ringer India Pale Ale Kit video, I take you step by step through unboxing, brewing and taste testing. This was ready to drink in just over a month. The first thing I did was heat approx 2.5 gallons of filtered water to 155F or approx 68F. Then take the provided grains, pour them into the grain bag, tie off the grain bag and place it into the water once it reaches temp. Maintain that temperature, no higher and no lower (plus or minus a couple degrees), and let it steep for 20 to 30 minutes. Once 20 to 30 minutes has elapsed, pull out the grain bag and let drain over the newly created wort. Don't squeeze it. Then it's time to bring the wort to a slow rolling boil. Total boiling time will be 60 minutes. Once boiling add the liquid malt extract. and stir in well. While it's boiling I added cool filtered water to the fermenter. I then added hops at 10 minutes time intervals and stirred them in. Once 60 minutes in complete I transferred the wort immediately to an ice bath. Once completely cooled I transferred (siphoned) the wort to the fermenter and topped it off with some additional filtered water. I then added the yeast and shook it around a little. Then I installed the air lock and let the brew sit for a couple weeks in a dark area. After a couple weeks I transferred it to a separate fermenter that was actually only used as a bottle filler and then mixed and added some hops and the priming sugar solution to give the brew carbonation. I then bottled it and let it sit for a couple weeks before sampling.

DIY Homemade Pallet Firewood Wood Storage Bin-Repurposed Pallet Wood Tur...

In this DIY Homemade Pallet Firewood Wood Storage Bin-Repurposed Pallet Wood video I demonstrate how to simply construct a useful and practical all weather log seasoning rack. Since I used so many pallet slats for other projects I had many of the big pallet cross member pieces left over. Typically I would slice them up into burnable pieces and use them for getting my fire started as they are great for this. In this case I needed racks in which to store all of my firewood so these were just what I needed. So I started sorting them out and getting 4 that were nearly identical to start out with and then of course pulling the nails out of pounding them in. In some cases I had to knock them off to the side and pound them flush. The reason to start out with 4 that are identical is so the sides will be close to equal height. For the bottom all you'll need is two that are nearly identical. The top is less important as long as you have pieces that are long enough as you can trim the top or even use slats if you have long enough ones. As far as the nails go, whenever I pulled them I tried to staighten them if needed and save them for future use. In this case I was able to reuse them for building these things. After sorting the pieces I laid them out on the ground in a "U" shape making two identical parts right next to each other. The bottom portion of the "U" gets nailed together to the side pieces. Once the two identical parts are constructed I stacked them on top of one another. I then used some pallet slats as securing pieces to hold the two modules together. After standing the pieces upright I completed the square by nailing the top portion on. This adds strength to the side pieces when storing firewood and also adds to the visual appeal. These are nice to make because they are free and also you can make as many as you want and stack them next to each other in a nice organized fashion without the fear of your firewood falling over. It also makes it easier to secure a tarp to it if you need to keep it dry.



www.diy-technician.com

How to Construct a Brick Fire Pit in your Back Yard

Placed a nice metal fire ring inside the brick for easy clean up and decoration. One nice thing about living where I do is that it's legal to have little backyard bonfires. Many good times are had with get togethers around a fire. I needed to move locations of my fire pit so I decided to make a video while I made this new one. To get started I marked a counterpoint in the middle of my rough circle and started over turning the dirt with a shovel and breaker bar as it was very tough and rocky. Then I started digging out the hole in the ground deep enough to accurate the height of my fire ring that I wanted to put in the ground. I decided I wanted to inset this one into the ground for the most part rather than have it be mostly above ground. Once I dug enough dirt out to where I thought it would be deep enough, I started to test fit the metal fire ring for depth purposes but then I also used it as the template for which to create the circular brick portion around. With my digging tools I started widening the circle a little bit to make it large enough to fit the bricks. It was important to keep the bottom flat so the the bricks would be level. Once I got the bottom of the pit level I used my 3 foot level to make sure it was level. I was then able to stack all of the bricks in there in a circular pattern and then add the metal fire pit inside it. It turned out just as I planned and ended up using it quite a bit.

Steve and Leif’s Digital Food Thermometer Review-Tested in Fresh Cooked ...

Ferrari Brand Bottle Tree-Home Brew Post-Sanitizing Bottle Drying Rack

This is a must-have if you are into home brewing and bottling. It allows you to wash and sanitize your bottles then place them in such a manner that allows the water to run out without the bottle being disturbed and falling over. A friend and fellow home brewer of mine showed me this thing and uses it all the time. What a great little effective contraption . The price you pay for this is well worth the convenience of it and the assembly on this was as easy as you get as well.

Here's the link to it: https://amzn.to/2DlBdAy


#bottle, #tree, #beer, #ferrari, #homebrew, #craft, #bottletree, #bottledryer, #sanitize, #wash, #sanitize, #clean, #rinse, #sterilize, #bottling, #beverage, #brewer

How To Fix a Leaky Toilet

This job started when I got notified about water on the floor. It would get cleaned up with a towel but show back up again. It would get worse after every flush of the toiled. I checked for the quick and easy stuff first. The toilet wasn't continually running, meaning, the float inside was good. I checked really good around the water supply valve, it's associated hose, and it's connection to the toilet. All of this was bone dry. This meant one thing,  Toilet was leaking around the base. This meant I had to perform the following steps to pull the toilet and replace the wax ring:



Step 1: Turn off the water to the toilet

Step 2: Flush remaining water in the bowl

Step 3: Disconnect water supply hose

Step 4: Remove the two caps over securing nuts on toilet base

Step 5: Unthread the two securing nuts

Step 6: Pull (remove) the toilet

Step 7: Remove old wax ring remnant

Step 8: Install new was ring

Step 9: Re-install toilet onto new wax ring



Here's a wax ring kit:

https://amzn.to/2RKA9it

What's Inside? Alpha Brand Fog Machine Model F80Z-Full Disassembly and ...

See what's Inside this Alpha Brand Fog Machine Fogmaker Model F80Z. Full Disassembly and Internal Component Removal process. This particular fog maker was in a non-working status which was what lead to it's disassembly. The hope was to open it up and find something obvious wrong with it that could be repair but it would not be. Upon disassembly it was unclear why it wasn't working so the full disassembly continued. It was quite interesting to see what is actually inside a fog maker. The parts that come out are interesting. I believe the aluminum piece inside is some sort of rapid chiller and vaporizer.

All I needed to take this apart was mainly a cordless drill with a Phillips head bit.

DIY How to Unclog a Bathroom Sink in Singapore

As a home dweller the chance of you having a clogged up drain are pretty good. The odds of having a clogged up drain go up the more people in the house you have. Once you have a clogged up drain and have procrastinated unclogging it long enough, you''ll be faced with two choices, DIY or all a professional. My thought is try to unclog it yourself and if you have no luck then it's time to call the pros and fork out some $$$. Follow along with me while I go through the process of a DIY How to Unclog a Bathroom Sink in Singapore. There are many ways to do this with household items but in many cases my trusty old pair of hemostats will do the trick. If you don't have them there are a number of household items that will do. Some of those are: A Wire Hanger.
Baking Soda and Vinegar. Mix baking soda with vinegar in a measuring cup, a Wet & Dry shop vacuum, Boiling Water, Cleaning the pipe, or caustic soda.
Another method commonly used is to use a clean plunger to plunge on the sink. The plunger method, however, will not serve you very well if there is a bunch of hair trapped around the drain. This works better if it's some debris caught down farther in the pipe. If the hemostat method doesn't work well for you from topside then it's a good idea to take apart your P-trap area.

DIY Buck Horn Mount from Pallet Wood and Bed Rails

I had to do this nice buck some justice by mounting his horns in this Instructional "how to" style video with detailed step by step procedural instructions for mounting buck horns out of pallet wood and a metal bedrail frame. The pallet I found happened to be a nice oak one. This project posed a few challenges and one of those was that the horns were in two pieces rather than one and there wasn't a heck of a lot of material to nail to the wooden back pieces. So to start I pulled the nails out of the oak pallet I had found and cut the cross members into three equally sized pieces for the mounting boards. It love the density of oak wood. It's so heavy too and really nice to work with. After getting the proper size I grabbed the scrap bed rail I had laying in the metal scrap pile and cut it to match the wood pieces. I took a power wire brush to the cute pieces and removed the paint followed by a coat of clear coat to the bed rails. I coated the wood with some clear varnish as well. Now I had to cut the horns to the proper angle in order to properly mount them to the wood. This took a few tries match it up so it looked both even and natural. I drilled a hole up through the horns then a hole I backboard as well once I got the horns in proper position. Then I hit it with a few brad nails and some epoxy. For the back I used an old pop can tab. Then I hung it up. Fun project made with all up cycled or reused materials.

DIY Pallet Project-Simple Wall Mounted Pallet Paint Shelf Organizer

With some simple hand tools and a free old pallet you can make an up cycled DIY Pallet Project-Simple Wall Mounted Pallet Paint Shelf Organizer in no time flat. When choosing pallets, if I have the option, I try to pick ones that have all of the slats in good shape and also I like to pick the ones that are a little heartier. It's not always an option and often times I've had to just settle with what I can get. It is never a waste though because if a pallet just went to hell when I was taking it apart, I'd just use it for firewood to generate heat. If I didn't use it in the fireplace I could use it for outdoor burning in the firepit. Pallet wood burns quick and lights up nicely prepping a good coal bed to toss some longer burning logs on. So, in making this wall mounted pallet shelf I easily cut my pallet roughly in half, using the middle cross member as my cut line so it was nice and straight. I wanted it a little smaller so I sectioned it off once again basically making a smaller rectangle out of the bigger one. This left me with a section of pallet containing four cross members. I then took my hammer and pryer and carefully removed every other wooden slat. I used one of those wooden slats as bottom piece for this shelf. I even removed as many nails as I could and straightened the salvageable ones for reuse. No use in tossing out a perfectly good nail. I then took my cordless drill and a few drywall screws and mounted this sucker to the outside of my shed. After I mounted it I cut some bottom pieces for the leftover scraps for the bottom portion of the upper shelf on this fixture. This worked out perfectly for my storage needs.

Tools used:
Handsaw: https://amzn.to/2BBD4Ag
(Optional)Skillsaw: https://amzn.to/2P9VJLJ
Crowbar: https://amzn.to/2MCjeuZ
Cordless Drill: https://amzn.to/2P9VTCP
Hammer: https://amzn.to/2N6XE0H

DIY Overhead Ceiling Electrical Light Fixture Removal

The first step in this DIY Overhead Ceiling Electrical Light fixture Removal Jon s to turn off the power. You'll want to do this first so you don't shock yourself. The next step is to unscrew the glass fixture cover by unthreading the center holding nut that holds the glass cover in place. Be careful as sometimes this could cause the glass to come down on you or drop on the floor depending on who installed it. Then unscrew the lightbulb. At this point you can unthread the center piece if need be, not required though.

The next step is to get your cordless drill and unscrew or loosed the two screws hold this into place. These are attached to the light fixture electrical box itself. Now give the fixture a little twist and it should come loose. If it's been up there a long time, expect some insulation, dust, and debris to come out so try not to get this on your face or into your eyes. Before touching any wire, I recommend doing a second check to make sure there is no current going through the wires. I always take three precautions when doing this kind of work. I shut the power off at the breaker, shut the power off at the switch, then finally use my voltage tester to make sure I don't get shocked. Once you've confirmed no current flowing through the wires you are about to touch, go ahead and untapped and unthread the existing house wire to remove this old fixture.

Here's an amazon link to a voltage tester: https://amzn.to/2ltV77h

Kwikset Door Knob and Dead Bolt Installation Instructions

DIY FIre Pit from Water Heater

How to install window screens on house windows

Step by step tutorial in the basics of installing a window screen. The side with the thin metal springy clips attached to it goes in first. The plastic tabs go inward as it makes it ever so slightly tougher to remove from the outside. The trick to getting all four corners inserted is to get three corners in first leaving one slightly out, then the fourth and final corner will barely slip in. In this example I put the right two corners in first because they had the metal spring tabs on them, followed by the upper left corner, then finally the bottom left corner.

Not sure if this is any good: https://amzn.to/34XDKNl

www.diy-technician.com

Hotpoint Brand Oven Light Bulb Installation

DIY "How to" Hotpoint Brand Oven Light Bulb Installation Tutorial Instructional Demonstration. If you know how to do this then its very easy, but for those of us who don't, well...it can take a minute or two to figure out. If you watch this video, I will show you exactly how to replace the bulb in your Hotpoint Brand Oven. Many people just leave the light bulb in the burned out state for the life of the oven. I couldn't imagine not being able to see what's cooking or what it's looking like.
Many people, like myself are procrastinators. "Well the oven light is out" is what you may tell yourself. It's tough to get in there and get after it as it's one of those things that you can make do without. That being said, it's much nicer to have a working oven light than not. So if you can find the gumption to change out the light bulb, pop open the oven door and get after it. The first thing you want to do is take the securing wire and push or pull it off to the side. This is your first access point to getting this done. Be careful not to drop the glass that goes over it as you do. You can do this all with one hand no problem. So what you want to do is move the wire over while keeping some pressure on the glass and once the wire is pushed over, than sort of captivate and capture the glass. This will allow you to gain access to the light bulb. You will need a headlamp or flashlight for this job. Now take the existing light bulb and unscrew it. Now take your new one and screw it in.
Anyway, hope this little quick video helps you out. Good luck!

Link to the light bulbs: https://amzn.to/2ZVjvOr

www.diy-technician.com